One of the causes of a stalled car on the way, the most common and difficult to repair is a dirty injector. Understandably, this device serves to fog spraying fuel into the engine combustion chamber."So, let bursts stopped completely, just hangs up or is not smooth combustion process is compromised," said Zaenal Arifin, Mechanical Companions Motor, Fatmawati, Cipete, South Jakarta, Saturday, June 18, 2011.As a result, the vehicle turned on even fussy alias difficult. Even the extreme, breaking down or the machine is turned difficult. Therefore, treat and prevent the injector problem is obligatory for us.Only, not least the ordinary car owners how to do that. In fact, how to check the condition of the injector and prevent the device was in trouble quite easily. You can take it to a repair shop that has equipment ultrasonic injector or detector.
So what steps is it? Here are tips from Zainal Arif :1. Check the voltage level of electrical current injectorOne of the many great workshops offered by the current inspection device's electrical voltage. As a measure commonly used is the current voltage at the engine off should be equal to the voltage at the battery."While at the time the injector is active, the opposite voltage sources from electronic control unit must not exceed 0.4 volts," said Zainal.When the voltage was normal but the injectors are not functioning normally, then the injector should be replaced immediately.Another way that is also often used the garage is to measure the impedance injectors with a Ohm meter. Impedance is a measure of the rejection of sinusoidal alternating current.Make sure the level is too low impedance and vice versa, is not too high. With a low impedance injector size is 3-5 ohms and 12-17 ohms to high impedance.Examination should be performed when the injector cold nor hot. When in hot conditions and high impedance levels, meaning injector problem and needs to be replaced soon.
2. Perform the following preventive measures;If it turns out the condition of electrical current injector is not problematic, then it should be done several ways of prevention by doing this:
a. Clean injector with ultrasonicIn a few workshops already available equipment. Its function is to clean the injector of the crust or dirt that clog. At the same time, ask your mechanic or a mechanic to check whether there was a leak in the device.In addition, make sure the pressure or spray mist of fuel into the engine combustion chamber is complete. Usually the service pack to fix prices injector cleaning service package is USD 250-350 thousand.
b. Check the condition of the fuel pump and related componentsThis examination aims to ensure the fuel pressure by the fuel pump. The way to ensure true quite easily, which is enough to feel the pressure in the fuel hose from the fuel pump to fuel filter.If it turns out the pressure feels sluggish, there is a problem in the fuel component. If you have any problems like this, try to check the fuel pressure regulator. These devices are generally rarely damaged, the most common complaints leveled the car owner is a leak.However, in order to check the fuel pump and all manner of related components is completed, you should drain the fuel tank. Clean channel leading to the combustion chamber and clean engine fuel filter
So what steps is it? Here are tips from Zainal Arif :1. Check the voltage level of electrical current injectorOne of the many great workshops offered by the current inspection device's electrical voltage. As a measure commonly used is the current voltage at the engine off should be equal to the voltage at the battery."While at the time the injector is active, the opposite voltage sources from electronic control unit must not exceed 0.4 volts," said Zainal.When the voltage was normal but the injectors are not functioning normally, then the injector should be replaced immediately.Another way that is also often used the garage is to measure the impedance injectors with a Ohm meter. Impedance is a measure of the rejection of sinusoidal alternating current.Make sure the level is too low impedance and vice versa, is not too high. With a low impedance injector size is 3-5 ohms and 12-17 ohms to high impedance.Examination should be performed when the injector cold nor hot. When in hot conditions and high impedance levels, meaning injector problem and needs to be replaced soon.
2. Perform the following preventive measures;If it turns out the condition of electrical current injector is not problematic, then it should be done several ways of prevention by doing this:
a. Clean injector with ultrasonicIn a few workshops already available equipment. Its function is to clean the injector of the crust or dirt that clog. At the same time, ask your mechanic or a mechanic to check whether there was a leak in the device.In addition, make sure the pressure or spray mist of fuel into the engine combustion chamber is complete. Usually the service pack to fix prices injector cleaning service package is USD 250-350 thousand.
b. Check the condition of the fuel pump and related componentsThis examination aims to ensure the fuel pressure by the fuel pump. The way to ensure true quite easily, which is enough to feel the pressure in the fuel hose from the fuel pump to fuel filter.If it turns out the pressure feels sluggish, there is a problem in the fuel component. If you have any problems like this, try to check the fuel pressure regulator. These devices are generally rarely damaged, the most common complaints leveled the car owner is a leak.However, in order to check the fuel pump and all manner of related components is completed, you should drain the fuel tank. Clean channel leading to the combustion chamber and clean engine fuel filter
No comments:
Post a Comment